Measurement of Vibration on The Alternator Due to The Influence of Rotation Speed

Subekti Subekti, Hadi Pranoto, Muhammad Nurul Hidayat, Basuki Dwi Efendy

DOI: https://doi.org/10.37869/ijatec.v2i1.44

Article Viewers

Abstract viewed: 115 times
PDF viewed: 51 times

Abstract


The alternator or dynamo ampere is a device that functions as a generator that produces alternating current (AC) and converts it to direct current (DC). Signs of damage that often occur due to damage to the Alternator are the smell of burning, squeaking, dim spotlights, indicator lights, malfunction of the battery, and the supply of electricity. These signs will cause the vehicle to stop in the middle of the trip the electricity supply is very lacking. This requires that preventive maintenance checks on the alternator are a must in the automotive world. In this paper we research measuring the vibration of the alternator due to the influence of rotation speed (750 rpm and 1800 rpm), to predict damage to the alternator of the Daihatsu Luxio vehicle. The results of this study indicate that at the rotational speed of 750 rpm and 1800 rpm, were found 1x rpm the condition of the vibration amplitude on the alternator is smaller than the alternator in poor condition, this is due to the presence of an unbalanced alternator. Also, vibration due to misalignment is obtained because it has characteristics, among others: vibrations with a frequency of 1xRPM and/or accompanied by a relatively large 2xRPM, and relatively high vibration in the axial direction.


Keywords


alternator; damage; vibration; unbalance; misalignment

Full Text:

PDF

References

D. Apriliananda, Kompas "Suara mesin bensin mirip diesel? Kenali penyebabnya!," Https://Otomotif.Kompas.Com/Read/2015/04/22/134316815/Suara.Mesin.Bensin.Mirip.Diesel.Kenali.Penyebabnya. Diakses: 27 Juli 2020

B. Prasanth, S. Wagh, S., and D. Hudson, "Alternator Whining Noise-A Sound Quality Concern In Passenger Car," Sae Technical Paper 2011-26-0018, 2011, Https://Doi.Org/10.4271/2011-26-0018.

R. Maladzi, T. Prahasto, A. Widodo, "Analisis Kerusakan Bantalan Gelinding Dengan Variasi Kecepatan Putar Berdasarkan Pola Getaran Menggunakan Metoda Envelope Analysis", Jurnal Teknik Mesin Universitas Diponegoro, V. 5, N. 1, Pp. 32-41, Jan. 2017.

M. Rivai, N. Pranandita, "Analisa Kerusakan Bantalan Bola (Ball Bearing) Berdasarkan Signal Getaran", Manutech, V. 10, N. 2, Pp. 41-46, 2018.

G.Z. Abidin, I.W. Sujana, "Deteksi Kerusakan Bearing Pada Condensate Pump Dengan Analisis Sinyal Vibrasi", Jurnal Flywheel, V. 8, N. 1, Pp. 60-67, 2017.

B.P. Kamiel, N. Prastomo, B. Riyanta, “Ekstraksi Parameter Statistik Domain Waktu Dan Domain Frekuensi Untuk Mendeteksi Kavitasi Pada Pompa Sentrifugal Berbasis Principal Component Analysis (Pca)”, Rekayasa Mesin , V. 10, N. 2, Pp. 165-176, Aug. 2019.

W. A. Curtis, "Electrical Signature Analysis Applications For Non-Intrusive Automotive Alternator Diagnostics," Technology Showcase: Integrated Monitoring, Diagnostics And Failure-Prevention. Proceedings of A Joint Conference, Mobile, Alabama, April 22-26, 1996.

W. Eversmann, S. Burnsa, S. Pekarek, Hua Bai, J. Tichenor,” Noise Generation Mechanisms In Claw Pole Alternators,” Journal Of Sound And Vibration 283 (2005) 369–400.

Mohammad Reza Asadi Asad Abad, Ashkan Moosavian, And Meghdad Khazaee," Wavelet Transform And Least Square Support Vector Machine For Mechanical Fault Detection Of An Alternator Using Vibration Signal," Journal Of Low-Frequency Noise, Vibration And Active Control 2016, Vol. 35(1) 52–63.

P. A. Vladimirovich, "Fault diagnosis in automotive alternators based on the output voltage parameters," International Conference on Electrotechnical Complexes and Systems (ICOECS), Ufa, Russia, 2019, pp. 1-5, DOI: 10.1109/ICOECS46375.2019.8949994.

A. Susanto, S.Q. Yusuf, A. Hamid, S. Subekti, “Implementation Of Frequency Response Function On Tapper Bearing Maintenance”, Sinergi, V. 23, N. 2, 2019.

O.D. Mohamad, M. Rantatalo, “Dynamic Response And Time-Frequency Analysis For Gear Tooth Crack Detection”, Mechanical System And Signal Processing, V. 66-67, Pp. 612–624, Jan. 2016.

I. Y. Shen, and E. M. Ladd, "Estimating Bearing Coefficients Of Fluid-Dynamic Spindle Motors Using Sub-Resonant Frequency Response," 2010 Apmrc, Singapore, 2010, Pp. 1-2

R. V. Daniel, S. A. Siddhappa, S.A., Gajanan, S.B., "Effect Of Bearing On Vibration In Rotating Machinery", In IOP Conf. Series: Materials Science And Engineering: International Conference On Material Alloys And Experimental Mechanics, India, 2017.

M. Ikhsan, A. P. Monika, D. O. Rio, H. Abdul, S. Subekti,” Analisis Getaran Tapered Roller Bearing Pada Turbine Propeller Sebelum dan Sesudah Pelumasan (Oli & Grease) Dengan Metode Bump Test,” Barometer, Volume 5 No.2, Juni 2020, 277-281.

Subekti, “Studying The Dynamic Characteristics To Lengthen The Operating Life For A Diesel Engine Using Frequency Response Function (Frf) Measurement”, Sinergi, V. 22, N. 3, 2018.

B. D. Effendi, Subekti, A. Hammid, “Karakteristik Dinamik Disc Brake Daihatsu Sigra 1200 Cc Dengan Metode Bump Test”, Flywheel: Jurnal Teknik Mesin Untirta, V. 5, N. 1, Pp. 14–19, April 2019.

S. Subekti, A. Hamid, B. D. Effendy, A. W. Biantoro, “Inspecting A Bump Test In The Maintenance Of A 1200-Cc Daihatsu Sigra Disc Brake”, Sinergi, V. 23, N. 3, Pp. 191-198, Okt. 2019.

A. W. Biantoro, H. Maryanto, A. K. Hidayanto, A. Hamid, “The Investigation Of End Mill Feeds On Cnc Router Machine Using Vibration Method”, Sinergi, V. 24, N. 2, Pp. 117-124, June 2020.

H. Sangian, D. A. Rahman, R. Rudiwanto, S. Subekti, A. Hamid, “Analisis Getaran Pada Screw Compressor Akibat Pengaruh Putaran Rotor”, Rekayasa Mesin, V. 11, N. 2, Pp. 267-275, 2020.

S. Subekti, M. N. Hidayat, B. D. Efendi, A. Hamid, A. Murwanto, “Hilbert Transform Analyzer For Mechanical Fault Detection Of Vehicle Alternators”, Automotive Experiences, V. 3, N.3, Pp. 89-95, 2020.

F. Homaei, S. Shojaee, G. G. Amiri, “Multiple-Structural Damage Detection Using Measured Frequency Response Function”, Iranian Journal of Structural Engineering. V. 2, N.1, Pp. 13-18, 2015.

R. M. Lin, “Modeling, Detection, And Identification Of Flexural Crack Damages In Beam Using Frequency Response Function”, Meccanica, V. 51, N. 9, Pp. 2027-2044, 2015.

A. B. Ghatwai, S. V. Chaitanya, S. B. Phadke, “Frequency Response Function Measurements Of Disc And Drum Brake With Its Verification By Cae”, International Research Journal Of Engineering And Technology, V.3, N. 5, Pp. 2223–2228, 2016.


Refbacks

  • There are currently no refbacks.

Share This Article



Copyright (c) 2021 International Journal of Advanced Technology in Mechanical, Mechatronics and Materials


IJATEC is indexed by the following abstracting and indexing services:


International Journal of Advanced Technology in Mechanical, Mechatronics and Material (IJATEC)
Institute for Research on Innovation and Industrial System (IRIS)
Jl.Raya Mustika Jaya No 88, Mustika Jaya, Bekasi Kota - 17158
Telp./Fax: +62 815-7499-5509
p-ISSN: 2720-8990
e-ISSN: 2720-9008
www.ijatec.com/index.php/ijatmmm



This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.